MikMek SubMicro Návod k obsluze Strana 1

MINI MODEL TICKET PRINTERS Operator’s Manual0,1,0%0,1,3/8668%0,1,;0,1, 90

98.0 Maintenance and AdjustmentsYour ticket printer is solidly constructed and has been designed for high volume use. It requires minimal care to p

108.1.1 Load Switch and Cut OptoThere is one micro switch located below the paper guide. This switch is used to sense the presence of ticket stock in

11There is one optical device mounted on an aluminum bracket. The opto controls the cut position. Removal or adjustment of the opto should be done w

128.1.2 THERMAL PRINT HEADThe print head should be cleaned periodically to prevent debris from building up on the print element. The required cleanin

13Click here to return to > Table of Contents8.1.3 Rubber Drive Roller (Platen)The rubber drive roller should be cleaned once a year to prevent pap

148.1.4 Ticket Width Adjustment To adjust the paper path for use with a different ticket width, loosen the two thumbscrews located on the adjustable s

158.2 Cutter Assembly The BOCA cutter (BC2) system is a fully integrated cutter knife mechanism powered by a stepper motor. The BC2 requires no adjus

168.3 Logic Board The printed circuit boards used in this product have been manufactured using surface mount technology. These printed circuit boards

178.3.2 Logic Board (Installation) 1. Align Main Logic Board so that the four mounting holes are above the four fasteners. 2. Press logic boar

18P50-1003 DRIVE BELT, 102T P50-1012 DRIVE BELT, 105T P50-1017 DRIVE BELT, 98T P51-1007 DRIVE PULLEY, 20T (Large ID .25") P51-1014 DRIVE PUL

1Table of Contents Page FCC Notice & Warranty Information 2 1.0 Introduction 3 2.0 Unpacking the

19421421-M41P TOP PLATE, VM SPECIAL for 2" & 3.25" fixed VM model printer (10.25" x 10.25") 421988-2 TOP PLATE, Dual Mini (3

20 a. Check for blockage in the cutter area. c. Default printer settings. With the printer powered off hold down the TEST button and then power up

21APPENDIX A - CONTROL PANEL The FGL44 printers allow the user to adjust various printer options through the control panel. To access the control pan

22The following is a brief overview of some representative Menu options: BAUD RATE? Controls the serial interface baud rate, parity bit, data bits an

23APPENDIX B - VERTICAL PRINTER INSTALLATION Prepare the counter top by cutting a rectangular hole in accordance with the dimensions specified for you

24APPENDIX C - DUAL MINI This section will go over some of the unique features of the Dual Mini model printer. • The Dual Mini has a load opto config

2FCC NOTICE NOTE: The equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rule

3

41.0 IntroductionThe BOCA MINI series printers are direct thermal ticket printers with an integrated cutting mechanism. This manual will provide the

53.0 Important Safety Information :$51,1*7KHDSSHDUDQFHRIWKLVV\PEROLQGLFDWHVWKHSUR[LPLW\RIDQH[SRVHGKLJKYROWDJHDUHD3OHDVHIROORZDOO

64.0 Installation The BOCA MINI series printer was designed to be mounted either on a desktop or shelf (horizontal model) or vertically in a counter t

76.0 Standard Interface Pinouts SERIAL PINOUTS RS232 (standard) RS232 (PC type)PIN FUNCTION PIN FUNCTION 2 Printer Transmit

87.0 Thermal Paper - Theory & SpecificationRefer to the BOCA Systems website at www.bocasystems.com, THERMAL TICKETS section for the most current